Optimal blendps is worst case 2 instructions.
FEX's RA doesn't quite get there since it can't see through multiple
instructions with SRA destinations. That'll be fixed in the future.
Optimal blendps is always one instruction, one is a no-op.
We always hit this.
Cleans up the code which had special cased some 32-bit optimization
which is unnecessary now that both 8-bit and 16-bit are also optimized.
When FEX does a VExtractToGPR, the result is zero extended to the full
GPR register size. This means we don't need to do a zero extend when
storing to a guest GPR.
Makes pextr{b,w} optimal now.
Needs #3088 merged first.
If CI faults out due to a bug then we would have no log as to which
instruction caused the issue.
I find myself adding this each time an assert fires to see what
instruction it was working on. Just add it directly.
I managed to miss a whole section of instructions from the secondary
opsize tables. This resulted in four instructions missing from the
database.
Adds cmppd, pinsrw, pextrw, and shufpd which are all non-optimal
instruction implementations.
In the case that source registers are sequential then this turns in to a
load of the vector constant (2 instructions) and the single tbl
instruction.
If the registers aren't sequential then the tbl turns in to 2 moves and
then the single tbl, which with zero-cycle rename isn't too bad.
Since this is a worst case option this is significantly better than the
previous implementation doing a bunch of inserts which was always 9
instructions.
We should still strive to implement faster versions without the use of
TBL2 if possible but this makes it less of a concern.
Skips implementing it for the x86 JIT because that's a bit of a
nightmare to think about.
The ARM64 implementation requires sequential registers which means if
the incoming sources aren't sequential then we need to move the sources
in to the two vector temporaries. This is fine since we have zero-cycle
vector renames and the alternative is slower.
Hits a whole bunch of common cases, most of which then emit optimal code
generation.
Two cases that use VInsElement hit the RA quirk where the SRA
destination is dead but RA doesn't see it, so it ends up doing a couple
moves. If RA gets fixed then those two moves will go away.
There are definitely still cases that we could emit more optimal code.
Additionally we could implement a TBL2 IR operation to do a LUT approach
for ones we don't cover.
Problem with implementing a TBL2 ir operation is that we have no way to
ensure registers are sequential so we would need to always do moves
```asm
ldr v2, <LUT Table>
mov v0, v16
mov v1, v18
tbl v16.16b, { v0.16b, v1.16b }, v2.16b
```
Which to be fair isn't terrible, and if we're lucky that the guest uses
sequential registers we can naturally get the more optimal code path.
Ideally our RA could push some operations in to sequential registers but
that's not possible currently.
I'll do a follow-up PR that implements TBL2.
Move instruction to itself here is a nop.
Need to be careful about AVX operations which use a different handler
since those might actually zero the upper bits on 128-bit move
{Load,Store}RegisterSRA always loads or stores GPRSize. 8-bit and 16-bit
are vestigial and all OpcodeDispatcher usage will load the full GPR size
(32-bit or 64-bit) and then extract or insert as necessary.
This cleans up a few bits of codegen in InstCountCI.
Currently FEX will always jump out of the JIT any time FCW was getting
written to, ensuring that the softfloat state is setup to rounding at
the time of FCW getting written.
This has the unintended side-effect that even in "x87 reduced precision"
mode we were jumping out of the JIT.
This hit a real world use case of an installer reloading FCW after every
x87 operation and generating a block with 2297 instructions.
Instead when jumping out of the JIT for handling x87 operations, load
FCW and pass it as the first argument of the handler. Setting the
softfloat state at that point.
This helps the installer's hottest block by cutting it down to 1477
instructions. 64.3% of the original size. The code block is still
burning 90% of the CPU time of the installer but the performance is
significantly better while it is doing its decompression.
In order to optimize this installer's block of code more then we will
likely need to optimize out x87 stack usage.
This leaves us with two temporary vectors that the JIT can use.
As of last month we stopped using v2 and v3 as temporaries and these can
now be given back to the JIT.
Ensures that the registers are still sequentially ordered and adds
support for spilling the FPR counts that are aligned by 2 instead of 4.
Adds a couple of instructions to filling and spilling but isn't that big
of an issue.
InstcountCI has some ridiculously large changes just because RA is
starting at a new register number.
This wasn't implemented initially for the interpreter and x86 JIT.
This meant we are maintaining two codepaths. Implement these operations
in the interpreter and x86 JIT so we no longer need to do that.
The emitted code in the x86 JIT is hot garbage, but it's only necessary
for correctness testing, not performance testing there.
Ryan Houdek